📦Free shipping over $10 in most countries and regions!



attachInterrupt()

[External Interrupts]

Description

Digital Pins With Interrupts

The first parameter to attachInterrupt() is an interrupt number. Normally you should use digitalPinToInterrupt(pin) to translate the actual digital pin to the specific interrupt number. For example, if you connect to pin 3, use digitalPinToInterrupt(3) as the first parameter to attachInterrupt().

BOARD DIGITAL PINS USABLE FOR INTERRUPTS

Uno, Nano, Mini, other 328-based

2, 3

Uno WiFi Rev.2, Nano Every

all digital pins

Mega, Mega2560, MegaADK

2, 3, 18, 19, 20, 21 (pins 20 & 21 are not available to use for interrupts while they are used for I2C communication)

Micro, Leonardo, other 32u4-based

0, 1, 2, 3, 7

Zero

all digital pins, except 4

MKR Family boards

0, 1, 4, 5, 6, 7, 8, 9, A1, A2

Nano 33 IoT

2, 3, 9, 10, 11, 13, A1, A5, A7

Nano 33 BLE, Nano 33 BLE Sense

all pins

Due

all digital pins

101

all digital pins (Only pins 2, 5, 7, 8, 10, 11, 12, 13 work with CHANGE)

Notes and Warnings

Note
Inside the attached function, delay() won’t work and the value returned by millis() will not increment. Serial data received while in the function may be lost. You should declare as volatile any variables that you modify within the attached function. See the section on ISRs below for more information.

Using Interrupts

Interrupts are useful for making things happen automatically in microcontroller programs and can help solve timing problems. Good tasks for using an interrupt may include reading a rotary encoder, or monitoring user input.

If you wanted to ensure that a program always caught the pulses from a rotary encoder, so that it never misses a pulse, it would make it very tricky to write a program to do anything else, because the program would need to constantly poll the sensor lines for the encoder, in order to catch pulses when they occurred. Other sensors have a similar interface dynamic too, such as trying to read a sound sensor that is trying to catch a click, or an infrared slot sensor (photo-interrupter) trying to catch a coin drop. In all of these situations, using an interrupt can free the microcontroller to get some other work done while not missing the input.

About Interrupt Service Routines

ISRs are special kinds of functions that have some unique limitations most other functions do not have. An ISR cannot have any parameters, and they shouldn’t return anything.

Generally, an ISR should be as short and fast as possible. If your sketch uses multiple ISRs, only one can run at a time, other interrupts will be executed after the current one finishes in an order that depends on the priority they have. millis() relies on interrupts to count, so it will never increment inside an ISR. Since delay() requires interrupts to work, it will not work if called inside an ISR. micros() works initially but will start behaving erratically after 1-2 ms. delayMicroseconds() does not use any counter, so it will work as normal.

Typically global variables are used to pass data between an ISR and the main program. To make sure variables shared between an ISR and the main program are updated correctly, declare them as volatile.

Syntax

attachInterrupt(digitalPinToInterrupt(pin), ISR, mode) (recommended)
attachInterrupt(interrupt, ISR, mode) (not recommended)
attachInterrupt(pin, ISR, mode) (Not recommended. Additionally, this syntax only works on Arduino SAMD Boards, Uno WiFi Rev2, Due, and 101.)

Parameters

interrupt: the number of the interrupt. Allowed data types: int.
pin: the Arduino pin number.
ISR: the ISR to call when the interrupt occurs; this function must take no parameters and return nothing. This function is sometimes referred to as an interrupt service routine.
mode: defines when the interrupt should be triggered. Four constants are predefined as valid values:

  • LOW to trigger the interrupt whenever the pin is low,

  • CHANGE to trigger the interrupt whenever the pin changes value

  • RISING to trigger when the pin goes from low to high,

  • FALLING for when the pin goes from high to low.

The Due, Zero and MKR1000 boards allow also:

  • HIGH to trigger the interrupt whenever the pin is high.

Returns

Nothing

Example Code

const byte ledPin = 13;
const byte interruptPin = 2;
volatile byte state = LOW;

void setup() {
  pinMode(ledPin, OUTPUT);
  pinMode(interruptPin, INPUT_PULLUP);
  attachInterrupt(digitalPinToInterrupt(interruptPin), blink, CHANGE);
}

void loop() {
  digitalWrite(ledPin, state);
}

void blink() {
  state = !state;
}

Interrupt Numbers

Normally you should use digitalPinToInterrupt(pin), rather than place an interrupt number directly into your sketch. The specific pins with interrupts and their mapping to interrupt number varies for each type of board. Direct use of interrupt numbers may seem simple, but it can cause compatibility trouble when your sketch runs on a different board.

However, older sketches often have direct interrupt numbers. Often number 0 (for digital pin 2) or number 1 (for digital pin 3) were used. The table below shows the available interrupt pins on various boards.

Note that in the table below, the interrupt numbers refer to the number to be passed to attachInterrupt(). For historical reasons, this numbering does not always correspond directly to the interrupt numbering on the ATmega chip (e.g. int.0 corresponds to INT4 on the ATmega2560 chip).

BOARD INT.0 INT.1 INT.2 INT.3 INT.4 INT.5

Uno, Ethernet

2

3

Mega2560

2

3

21

20

19

18

32u4 based (e.g Leonardo, Micro)

3

2

0

1

7

For Uno WiFiRev.2, Due, Zero, MKR Family and 101 boards the interrupt number = pin number.